Wolfland Computers & Hobby
423 E Sheridan St
Ely, MN 55731
218-365-7500
info@wolfland.net


Store Hours:
10 am - 5 pm Weekdays
Computer Emergency:
218-349-8650 (cell)

 

Wolfland Computers and Hobby
 

 
Wolfland Home

smartplane
 
R/C DHC-2 Beaver
hurricane
Hobby Shop Contents
rc repair
3D Printed Planes
v2
Estes Rockets
 
  3D Printing Services - Ham Radio |  3dlabprint.com Planes  |  Baby Canoes
A great Bitx40 website by Ryan Flowers is here.
Please add info at wolfland dot net to your address book to prevent my return messages from going to spam.
Hint:  Use a forstner bit to drill precise holes.
Some pieces will have to be glued together.  I have to print separately so they turn out correctly.
CA glue works best with activator but superglue works too.
Otherwise hinges can be added for future mods.
There is no heatsink hole on the IK8YFW and M6YPA enclosures.
There is a heatsink hole on the KE0KHA and KG7UMN enclosure.
Notice:  KE0KHA uBitx Cases, Prior to 2/15/18, the aluminum tape accessory is an addition after the initial design of the ubitx enclosures and needs to be applied
very flat on the bottom otherwise pcb component leads can come into contact with it.  Trim leads if necessary.
The plateau on the inside bottom of the cases
is now removed and the rail slot is raised so there will be extra space.
Apply the tape with no wrinkles on the bottom especially.
paypalsecure

 
Enclosure Accessories

alum 
Notice:  Put tape very flat on bottom of enclosure.
Try not to have any wrinkles which
can touch circuit board leads.
Add Aluminum Tape for
Increased RFI Protection
 
5' - 6' for $3.00
 

coverFront Cover for M6YPA Case
Also Includes Personalized Nameplate.
Add Hinges and or Latches from h/w store.
Note:  Hinge at bottom for angled display
 $19.95 Free Shipping Conus
Blue Transparent Frosty Shown.
 
Callsign and Color
bitx40
 
ubitx
 
Embed Your Callsign
or Printed Callsign for $10

  If you already have a uBITX or Bitx40 enclosure
I will 3d print you a label with your callsign for the same price and free shipping CONUS.  Please specify callsign below.
   
Specify:
Callsign

 
uBITX Enclosures
Frosty Transparent Clear and
Frosty Transparent Orange >
 
 
ubitx
Dark Blue
 
ubitx
 
ubitx
 
ubitx
 
  Voltage Regulator Cutout Option
  Left Side
Will ship without unless selected as an option.
slot
KE0KHA uBITX Enclosure
Carbon Fiber / PLA Mix
 
Pre-drilled holes and plenty of bosses.
Power and VFO Knobs Included.
   
  $36.00 Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
 
Rear Panel
Left Side VR Cutout
   
 

  Add Callsign on Carbon Fiber Front Panel
for $8.00 Instead of $10.00.
 


 
ubitx
 
ubitx
Orange and Red Shown.
 
 
Voltage Regulator Cutout Option
  Left Side
Will ship without unless selected as an option.
 
ubitx
KE0KHA uBITX Enclosure
 
Pre-drilled holes and plenty of bosses.
Power and VFO Knobs Included.
 
$29.95 Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
 
If you select Transparent Option, please specify
color in text box.  Because there is thickness to these
cases they print opaque with a shade of whatever color
you choose.  It looks frosty.

 
        
Color
Rear Panel
Left Side VR Cutout
Transparent/Frosty Org, Blu. Purple or Clear
   
Definition of boss:
https://www.merriam-webster.com/dictionary/boss
In other words it gives the user a place
for the screw to secure itself.
ubitxKE0KHA uBITX Enclosure
GRAB BAG
Pre-drilled holes and plenty of bosses.
Power and VFO Knobs Included.
     
$25.00 Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
 
This is a unique enclosure because it will be made of multiple colors.  I have a lot of rolls of colors with just a small amount of PLA so I have to use it up.  This is a FUN enclosure for the STRONG OF HEART.  Not a misprint.  If you are nice to me I will include a 3d printed front panel callsign label for your endeaver.  You get what you get and you don't have a fit.
THANKS SO MUCH!
 
Callsign
 
ubitxmods
US Army Green
KE0KHA uBITX Enclosure
Mods Version
$44.00 Free Shipping CONUS
$54.00 for Carbon Fiber PLA

Power and VFO Knobs Included.
Room for your mods
Walls are 4mm thick
Bosses to attach the front cover with screws
Sides and rear are attached to the base
Rails and pads to secure circuit board.
Cover has 6 bosses to secure with screws on all sides.
200mm W x 200mm L x 77mm H
(8" x 8" x 3")
 
Email to specify customizations or if you are an international buyer.
 
Colors
 
BITX40 Enclosures
Dual Purpose Enclosures
 
bitx40
Red
W7RLF Bitx40 Enclosure
Ryan's Design.
Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
 
6" W x 7" L x 3.5" Rear H, 1.75" Front H
The only holes are for the speaker and display
so you can do your mods.
Display bezel included.
Power and VFO Knobs Included.
 
 
Colors
ubitx
Red
W7RLF Dual Purpose Enclosure
Bitx40 or uBitx
Ryan's Design.
3/4" Wider to handle either radio and/or mods.

Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
 
6.75" W x 7" L x 3.5" Rear H, 1.75" Front H
The only holes are for the speaker and display
so you can do your mods.
Display bezel included.
Power and VFO Knobs Included.

 
Colors
bitx40
 
KG7UMN Bitx40 Enclosure
Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
Power and VFO Knobs Included.
 
 
Colors
 
ik8yfw
 
  
IK8YFW Bitx40 Enclosure
Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
Power and VFO Knobs Included.
 
 
Colors

 
 
m6ypa
 
M6YPA Bitx40 Enclosure
Free Shipping CONUS
Front Panel Bosses included.
Knobs Included.

Email to specify customizations or if you are an international buyer.
 
 
Colors
Standoff Pads for PCB
 
m6ypa
 
Extra Large M6YPA Bitx40 Enclosure
35mm longer and deeper,
Free Shipping CONUS
Email to specify customizations or if you are an international buyer.
Power and VFO Knobs Included.
 
 
Colors

 
 
Misc. / Misprints
Prototype Enclosures
 

 
wedge
 
Wedge for M6YPA Case, Also Includes
Personalized Nameplate.  $17.95
Free Shipping Conus.
Case sold separately.
 
Callsign and Color
ubitx Prototype KE0KHA uBITX Enclosure
Mods Version
No bosses on Front, less on top
Cover rear edge is rough.
Cover is gray like case, Front is dark brown
$30.00 Free Shipping CONUS

(Normally $47.00)

Room for your mods
Walls are 4mm thick
Sides and rear are attached to the base
Rails and pads to secure circuit board.
215mm W x 200mm L x 77mm H
(8.5" x 8" x 3")
Power and VFO Knobs Included.
 

hanger
 
hanger
Prototype KE0KHA uBITX Enclosure
Ruggedized Large Hanger
Multiple Color
$40.00 Free Shipping CONUS
(Normally $57)
Circuit board hangs from the top.
Room for your mods and batteries.
Walls are 4mm thick
Bosses to attach the front cover with 6 screws
Sides and rear are attached to the base
Rails, standoffs & pads to secure circuit board.
Cover has 6 bosses to secure with screws on all sides.
(prototype shown doesn't have bottom center boss)

215mm W x 200mm L x 105mm H
(8.5" x 8" x 4")
Power and VFO Knobs Included.
 


ubitxMisprint KE0KHA uBITX Enclosure
$19.00
The base printed fine but I had to repair the sides with Tamiya putty and light blue spray paint.  The inside bottom is nice but the sides looks like hell.  The outsides are acceptable.  Fully functional.  Let me know if you want all parts the same color in the comments below.  No problem.  The case comes with knobs.  Thank You.
 
Special Instructions
 
Other Enclosures

 
 
qcx
 Carbon Fiber
 
QRP Labs QCX Enclosure by G8XUL
SHORT VERSION
Width:  4.25"
Depth:  3.75"
Height:  1.5"
 
Email to specify customizations or if you are an international buyer.
   
Colors
qcx
QRP Labs QCX Enclosure by G8XUL
REGULAR VERSION
Width:  4.25"
Depth:  5.5"
Height:  2.0"
 
Email to specify customizations or if you are an international buyer.
   
Colors
capVariable Capacitor Enclosure
Width:  10.6"
Depth:  6"
Height:  5.6"
 
Free Shipping CONUS
 
Color
     

Home     |     Computer Repair and More     |     Hobby Shop Online Store     |     About Us     |     Contact Us
   
218-365-7500     |      Wolfland Computers     |     423 E Sheridan St     |     Ely, MN 55731     |     info@wolfland.net